12 A 32 Vac Fast-Acting Glass Fuse - Eaton AGC-12-R
12 A 32 Vac Fast-Acting Glass Fuse - Eaton AGC-12-R

12 A 32 Vac Fast-Acting Glass Fuse - Eaton AGC-12-R

Share
Eaton AGC-12-R: 12 A fast-acting glass tube fuse, 32 Vac, 1/4 x 1-1/4 in (6.3 x 32 mm), single element.
    • Product Details
    • Download

    Eaton AGC-12-R 12 A 32 Vac Fast-acting Glass Tube Fuse

    12 A at 32 Vac - fast-acting, glass body, 1/4 x 1-1/4 in, single element. Breaking capacity 35 A at 250 Vac up to 3 A, 100 A at 250 Vac from 1-1/4 A, 1,000 A at 32 Vac.

    Specifications

    Part numberAGC-12-R
    BodyGlass tube, 1/4 x 1-1/4 in (6.3 x 32 mm)
    Rated current12 A
    End capsnickel-plated brass
    Typical voltage drop0.138 V
    AC interrupting rating1,000 A at 32 Vac
    Elementsingle element
    Design standardUL 248-14
    Typical melting I2t696.96 A²s
    Typical DC cold resistance0.006 Ω
    Voltage rating32 Vac
    Breaking capacity35 A at 250 Vac up to 3 A, 100 A at 250 Vac from 1-1/4 A, 1,000 A at 32 Vac

    How This Fuse Behaves

    A fast-acting fuse is a single element sized to melt quickly once the current passes its rating. There is no thermal mass held back for a surge, so the response to an overload is immediate and the response to an inrush is equally immediate - the two are the same event as far as the element is concerned.

    What the Figures Mean

    The secondary columns are where the engineering hides. The typical cold resistance is 0.006 Ω, which is what the circuit sees before the element warms. Melting takes 696.96 A²s, so a fault has to deliver that much energy before the element even starts to go. At rated current the drop across it is 0.138 V. The current and voltage ratings only say when they matter.

    Reading the Part Number

    AGC is the family and 12 is the ampere rating, 12 A. The trailing -R marks the RoHS version; a packaging prefix such as BK- or BK1- may be added in front, which alters the quantity per box only.

    Where This Rating Sits

    Above roughly ten amps the fuse is protecting wiring and busbars rather than a component. The relevant question stops being "will it open" and becomes "what does it let through while it opens", which is what the I2t figure describes.

    The step below is AGC-10-R at 10 A, the step above is AGC-14-R at 14 A. Between the three the body, the end caps and the breaking capacity are identical; only the element changes, so the choice is the load current and nothing else.

    Standards and Approvals

    UL Listed and CSA certified (Guide JDYX, File E19180).

    Where the equipment ships into several markets, check each approval separately - the European and North American marks on this family do not always cover the same current range, and the gap is usually at the top of the range.

    Selecting and Replacing

    AGC is the fast-acting half of the MDL/AGC pair. Putting an AGC into a motor circuit that was engineered around MDL will nuisance-trip on every start, and the usual response - fitting a bigger AGC - removes the protection the circuit was designed for.

    For a like-for-like replacement, match three things: 12 A, fast-acting speed, and a voltage rating at least as high as the circuit can apply. Everything else about the part - the cap plating, the marking, the packaging prefix - is a purchasing detail rather than an electrical one.

  • Store glass tubes in their packaging. Loose in a bin, the end caps scuff and the marking becomes unreadable, which is how the wrong rating gets fitted.
  • Common Questions

    What is the difference between 3AG and 3AB?
    Both are 1/4 x 1-1/4 in. 3AG is the glass body, 3AB is the ceramic one. The footprint is identical; the breaking capacity is not.

    What happens if I fit a lower rating?
    It will open on normal load, usually at the least convenient moment. A fuse is not a safety margin to be tightened - it is sized to the cable and the load, and reducing it does not add protection, it adds failures.

    Why does the table list several breaking capacities?
    Because the fuse is asked to interrupt different currents at different voltages. The 250 Vac figure is usually the smallest and the 32 V figure the largest, since a low voltage is much easier to break than a high one.

    Design note: the ratings above are Technical Data 2543. Verify the exact rating, the voltage at which the breaking capacity applies, and the certificate for this current before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products