3216FF2.5-R 2.5 A 1206 (3216 metric) Fast-Acting SMD Fuse | 32 Vac/63 Vdc | Eaton Bussmann
3216FF2.5-R 2.5 A 1206 (3216 metric) Fast-Acting SMD Fuse | 32 Vac/63 Vdc | Eaton Bussmann

3216FF2.5-R 2.5 A 1206 (3216 metric) Fast-Acting SMD Fuse | 32 Vac/63 Vdc | Eaton Bussmann

Share
3216FF2.5-R: 2.5 A 1206 fast-acting SMD fuse chosen for compact electronic subsystems with a 2.5 A continuous-current requirement; 32 Vac/63 Vdc, 50 A interrupting rating, AEC-Q200 qualified.
    • Product Details
    • Download

    Eaton Bussmann 3216FF2.5-R 2.5 A 32 VAC / 63 VDC Fast-Acting 1206 SMD Fuse

    The Eaton Bussmann 3216FF2.5-R is a 2.5 A fast-acting Chip™ fuse in a 3216 metric (1206 imperial) surface-mount package. It is rated at 32 VAC / 63 VDC with 50 AAC/ADC interrupting capability. This intermediate rating can tighten coordination between 2 A and 3 A branches. The lower typical resistance than smaller ratings also helps reduce steady-state voltage loss at higher operating currents.

    Best fit: protecting 2.5 A electronics loads while preserving a 63 VDC rating in a 1206 footprint. Key check: confirm the normal load, startup waveform, available fault current and ambient-temperature derating before approval.

    Why Choose This Rating

    • 2.5 A fast-acting protection for 32 VAC / 63 VDC circuits
    • Typical cold resistance of 0.046 Ω and typical voltage drop of 0.14 V
    • Typical melting I²t of 0.260 A²s for pulse and coordination review
    • AEC-Q200 qualified within Eaton's 250 mA to 7 A range
    • Halogen-free, lead-free and RoHS compliant; MSL 1

    Core Specifications

    ParameterValue
    Manufacturer / SeriesEaton Bussmann series / 3216FF
    Part number3216FF2.5-R
    Fuse characteristicFast-acting
    Rated current2.5 A
    AC voltage rating32 VAC
    DC voltage rating63 VDC
    Interrupting rating50 AAC/ADC
    Typical DC cold resistance0.046 Ω
    Typical melting I²t0.260 A²s
    Typical voltage drop0.14 V
    Body marking2.5
    Package1206 imperial / 3216 metric SMD
    Operating temperature-55 °C to +125 °C
    Agency / environmentalcURus recognized; CSA component accepted; RoHS compliant; halogen-free; lead-free

    Best-Fit Applications

    • Distributed power-board branches
    • Communication equipment power inputs
    • Compact charging and power-management modules

    Selection Guidance

    The fuse is designed to carry rated current for at least four hours under the datasheet test conditions. Eaton recommends an operating current of 80% or less of the 2.5 A rating, with additional derating at elevated ambient temperature. That guideline is not a substitute for checking the time-current curve against startup and fault waveforms.

    For PCB design, use the manufacturer-recommended land pattern and mount the ceramic (white) side facing up. Also verify that the prospective fault current does not exceed 50 AAC/ADC at the applied voltage.

    Frequently Asked Questions

    Is 3216FF2.5-R AEC-Q200 qualified?
    Yes. Its current rating falls within Eaton's stated 250 mA to 7 A qualified range.

    Can it run continuously at 2.5 A?
    Designing at or below about 80% of rated current is recommended, followed by temperature and waveform validation.

    Is this a high-inrush fuse?
    It is a fast-acting fuse. If the load has significant inrush, compare the pulse energy and time-current profile with the curves rather than selecting by current rating alone.

    Ordering and Packaging

    Packaging: TR prefix, 3,000 fuses on 8 mm tape-and-reel, 7-inch (178 mm) reel, EIA-481.

    Ordering reference: specify the packaging code with the product code, for example TR/3216FF2.5-R. Confirm the exact orderable code and stock status before purchase.

    Design note: Electrical values are typical unless identified as ratings. Verify the latest Eaton datasheet and design curves before final release.

    Mechanical Dimensions

    eaton-3216ff-surface-mount-fuse-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products