Eaton AMLV04V05C033 5.5 V Multilayer Varistor
Eaton AMLV04V05C033 5.5 V Multilayer Varistor

Eaton AMLV04V05C033 5.5 V Multilayer Varistor

Share
AMLV04V05C033: multilayer varistor ESD suppressor, 8.8-13.2 V varistor voltage, 5.5 V working, 31 V clamp, 33 pF, 0.02 J.
    • Product Details
    • Download

    Eaton AMLV04V05C033 5.5 V Multilayer Varistor

    AMLV04V05C033 at a glance: multilayer varistor ESD suppressor, 8.8-13.2 V varistor voltage, 5.5 V working, 31 V clamp, 33 pF, 0.02 J.

    Key Specifications

    ParameterValue
    Orderable part numberAMLV04V05C033
    Working voltage, DC5.5 Vdc
    Working voltage, AC4 Vac
    Varistor voltage at 1 mA8.8 V to 13.2 V
    Clamping voltage at 1 A31 V
    Energy absorption, 10/1000 us0.02 J
    Peak current, 8/20 us4 A
    Typical capacitance at 1 MHz33 pF
    Leakage current at working voltagemax. 20 uA
    Package0402 (1005 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1078

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 2.82 times the varistor voltage: 31 V at the rated current against 11 V at 1 mA. That ratio is what the downstream part has to survive, not the 11 V figure on the label.

    Standing at 5.5 V the leakage is at most 20 uA, which is 0.11 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 33 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the AMLV family this is item 1 of 28 in the Eaton catalogue.

    Series Positioning

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products