Eaton AMLV12V34C550 1206 Chip Varistor 34 Vdc
Eaton AMLV12V34C550 1206 Chip Varistor 34 Vdc

Eaton AMLV12V34C550 1206 Chip Varistor 34 Vdc

Share
AMLV12V34C550: multilayer varistor ESD suppressor, 42.3-51.7 V varistor voltage, 34 V working, 77 V clamp, 550 pF, 0.4 J.
    • Product Details
    • Download

    Eaton AMLV12V34C550 1206 Chip Varistor 34 Vdc

    AMLV12V34C550 at a glance: multilayer varistor ESD suppressor, 42.3-51.7 V varistor voltage, 34 V working, 77 V clamp, 550 pF, 0.4 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberAMLV12V34C550
    Working voltage, DC34 Vdc
    Working voltage, AC26 Vac
    Varistor voltage at 1 mA42.3 V to 51.7 V
    Clamping voltage at 1 A77 V
    Energy absorption, 10/1000 us0.4 J
    Peak current, 8/20 us200 A
    Typical capacitance at 1 MHz550 pF
    Vjump (5 min)50 V
    WLD (10 pulses)1.5 J
    Leakage current at working voltagemax. 20 uA
    Package1206 (3216 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1078

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    These parts are zinc oxide ceramics sintered into a chip, so the response is faster than a junction device and there is no wear-out mechanism below the rated energy. What does degrade them is repeated energy above the rating, which shows up as a falling varistor voltage.

    The clamp column works out at 1.64 times the varistor voltage: 77 V at the rated current against 47 V at 1 mA. That ratio is what the downstream part has to survive, not the 47 V figure on the label.

    Standing at 34 V the leakage is at most 20 uA, which is 0.68 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 550 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the AMLV family this is item 15 of 28 in the Eaton catalogue.

    What This Family Is For

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products