Eaton AMLV18V30C1700 30 V Multilayer Varistor
Eaton AMLV18V30C1700 30 V Multilayer Varistor

Eaton AMLV18V30C1700 30 V Multilayer Varistor

Share
AMLV18V30C1700: multilayer varistor ESD suppressor, 35-43 V varistor voltage, 30 V working, 77 V clamp, 1700 pF, 3.8 J.
    • Product Details
    • Download

    Eaton AMLV18V30C1700 30 V Multilayer Varistor

    AMLV18V30C1700 at a glance: multilayer varistor ESD suppressor, 35-43 V varistor voltage, 30 V working, 77 V clamp, 1700 pF, 3.8 J.

    Key Specifications

    ParameterValue
    Orderable part numberAMLV18V30C1700
    Working voltage, DC30 Vdc
    Working voltage, AC23 Vac
    Varistor voltage at 1 mA35 V to 43 V
    Clamping voltage at 1 A77 V
    Energy absorption, 10/1000 us3.8 J
    Peak current, 8/20 us600 A
    Typical capacitance at 1 MHz1700 pF
    Vjump (5 min)45 V
    WLD (10 pulses)6 J
    Leakage current at working voltagemax. 20 uA
    Package1812 (4532 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1078

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    These parts are zinc oxide ceramics sintered into a chip, so the response is faster than a junction device and there is no wear-out mechanism below the rated energy. What does degrade them is repeated energy above the rating, which shows up as a falling varistor voltage.

    The clamp column works out at 1.97 times the varistor voltage: 77 V at the rated current against 39 V at 1 mA. That ratio is what the downstream part has to survive, not the 39 V figure on the label.

    Standing at 30 V the leakage is at most 20 uA, which is 0.6 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 1700 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the AMLV family this is item 25 of 28 in the Eaton catalogue.

    What This Family Is For

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message