Eaton CLB1108-4-50TR-R Multi-Phase Power Inductor, 4 phases, 50 nH per phase
Eaton CLB1108-4-50TR-R Multi-Phase Power Inductor, 4 phases, 50 nH per phase

Eaton CLB1108-4-50TR-R Multi-Phase Power Inductor, 4 phases, 50 nH per phase

Share
Eaton CLB1108-4-50TR-R: 4-phase multi-phase power inductor, 50 nH per phase, 0.28 mOhm DCR, 25 A rated per phase.
    • Product Details
    • Download

    Eaton CLB1108-4-50TR-R Multi-Phase Power Inductor, 4 phases, 50 nH per phase

    CLB1108-4-50TR-R: 4-phase power inductor, OCL 200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A, DCR 0.28 mOhm, 25 A per phase.

    Key Specifications

    ParameterValue
    Orderable part numberCLB1108-4-50TR-R
    Rated inductance per phase50 nH ±20%
    Number of phases4
    Open circuit inductance (OCL)200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A
    DC resistance (DCR)0.28 mOhm
    Rated current per phase25 A
    Peak current per phase110 A
    PackageCLB1108 footprint (see drawing)
    PackagingTR - tape and reel
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    With 4 phases of 50 nH each, the ripple on a given rail is the sum of the individual phase currents. Adding phases does not just divide the current - it also shapes the ripple, which is why the phase count is part of the VRM design rather than a purchasing decision.

    DCR 0.28 mOhm is why the 4-phase version exists. Halving the current per phase by doubling the phase count cuts the loss per phase by four, and the total inductor loss with it.

    Where This Series Fits

    CLB1108 是 50 nH 多相电感,给出 OCL 在 Isat1 与 Isat2 两个偏置点的值。

    • Typical use: 多相 VRM、高频大电流供电.
    • CLB 的 OCL 随偏置下降得比标准件慢(150 nH @25 A),这是它相对同尺寸其它系列的核心差别。
    • Data sheet Volterra; test conditions 1 MHz / 0.1 Vrms, +25 °C unless stated.

    Isat marks where the part leaves its inductive region. At 25 A the inductance has already dropped well below its open-circuit value, so a design that runs close to that point trades ripple control for headroom. 4 phases is the common configuration for a mid-power VRM. The phase count is set by the converter, not by the inductor - what matters here is that this part is the 4-phase variant with the matching pinout and DCR.

    Frequently Asked Questions

    Which inductance should I use?
    The rated inductance per phase, not the OCL. OCL is measured at zero bias; FLL is what the part has at rated current and it is the number the ripple calculation needs.

    Can I use fewer phases than the part number?
    No. The part number fixes the phase count and the pinout that goes with it.

    Is this part RoHS compliant?
    Yes - the -R suffix on the part number denotes the RoHS build.

    Design note: use the full-load inductance and the hot-case
    DCR for the loss budget, and check the layout keeps each phase current loop closed.

    Mechanical Dimensions

    eaton-clb1108-multi-phase-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products