Eaton CLB1108-5-50TR-R - 5-Phase 50 nH per phase Power Inductor, 0.28 mOhm DCR
Eaton CLB1108-5-50TR-R - 5-Phase 50 nH per phase Power Inductor, 0.28 mOhm DCR

Eaton CLB1108-5-50TR-R - 5-Phase 50 nH per phase Power Inductor, 0.28 mOhm DCR

Share
Eaton CLB1108-5-50TR-R: 5-phase multi-phase power inductor, 50 nH per phase, 0.28 mOhm DCR, 25 A rated per phase.
    • Product Details
    • Download

    Eaton CLB1108-5-50TR-R - 5-Phase 50 nH per phase Power Inductor, 0.28 mOhm DCR

    CLB1108-5-50TR-R: 5-phase power inductor, OCL 200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A, DCR 0.28 mOhm, 25 A per phase.

    Key Specifications

    ParameterValue
    Orderable part numberCLB1108-5-50TR-R
    Rated inductance per phase50 nH ±20%
    Number of phases5
    Open circuit inductance (OCL)200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A
    DC resistance (DCR)0.28 mOhm
    Rated current per phase25 A
    Peak current per phase110 A
    PackageCLB1108 footprint (see drawing)
    PackagingTR - tape and reel
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    With 5 phases of 50 nH each, the ripple on a given rail is the sum of the individual phase currents. Adding phases does not just divide the current - it also shapes the ripple, which is why the phase count is part of the VRM design rather than a purchasing decision.

    Copper loss rises with temperature - roughly half the DCR change over the working range. A part running hot is a part with more loss, which is a feedback loop worth keeping an eye on in a densely populated board.

    Where This Series Fits

    CLB1108 是 50 nH 多相电感,给出 OCL 在 Isat1 与 Isat2 两个偏置点的值。

    • Typical use: 多相 VRM、高频大电流供电.
    • CLB 的 OCL 随偏置下降得比标准件慢(150 nH @25 A),这是它相对同尺寸其它系列的核心差别。
    • Data sheet Volterra; test conditions 1 MHz / 0.1 Vrms, +25 °C unless stated.

    Saturation is a hard limit, not a derating curve. In a multi-phase converter the phases share the load, so a single phase that saturates first takes the whole transient on its own shoulders. 5 phases is a high-current configuration. Per-phase current is low enough that copper loss stays small even with 25 A in each winding, which is the whole point of going to this many phases.

    Frequently Asked Questions

    Which inductance should I use?
    The rated inductance per phase, not the OCL. OCL is measured at zero bias; FLL is what the part has at rated current and it is the number the ripple calculation needs.

    Can I use fewer phases than the part number?
    No. The part number fixes the phase count and the pinout that goes with it.

    How do the phases connect?
    The datasheet gives the pin numbering for each phase pair - (3-4)(5-6) and so on - and the layout has to keep each phase current loop tight.

    Design note: use the full-load inductance and the hot-case
    DCR for the loss budget, and check the layout keeps each phase current loop closed.

    Mechanical Dimensions

    eaton-clb1108-multi-phase-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message