Eaton CMS2-12-R Surface-Mount Common-Mode Choke 915 uH
Eaton CMS2-12-R Surface-Mount Common-Mode Choke 915 uH

Eaton CMS2-12-R Surface-Mount Common-Mode Choke 915 uH

Share
Eaton CMS2-12-R: 915 uH common-mode inductor, 0.67 A Irms, 0.33 ohm DCR, surface mount.
    • Product Details
    • Download

    Eaton CMS2-12-R Surface-Mount Common-Mode Choke 915 uH

    CMS2-12-R: common-mode choke, OCL 915 uH minimum, 0.67 A Irms, leakage 6.3 uH.

    Electrical Specifications

    ParameterValue
    Orderable part numberCMS2-12-R
    Open circuit inductance (OCL)915 uH minimum, (1-2) & (4-3)
    I rms (max)0.67 A
    DCR typical @ 20 °C (1-2)0.33 ohm
    DCR typical @ 20 °C (4-3)0.33 ohm
    Leakage inductance typ6.3 uH
    Interwinding capacitance typ4.9 pF
    PackageCMS series, surface mount
    Operating temperature160 °C maximum
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    A common-mode choke puts the same current through both windings in the same direction, so the differential signal passes through untouched while the common-mode noise sees the full impedance. It is the cheapest way to bring a switching node inside the emissions limit.

    Interwinding capacitance is the mechanism behind the high-frequency behaviour: above the capacitance the choke stops blocking and starts passing. Leakage inductance is the part of the inductance that escapes the core and does not help. 915 uH is a high-inductance part with a correspondingly low 0.67 A Irms. The trade is deliberate - you give up current capability to get attenuation down low in the band where the noise actually lives.

    Where This Series Fits

    CMS 是贴片共模电感,CMS1 / CMS2 / CMS3 三个尺寸系列,4.5 uH 到 1310 uH。

    • Typical use: 开关电源输出滤波、DC-DC 共模抑制、EMI 整改.
    • CMS 的 OCL 是在 (1-2) 与 (4-3) 两组绕组上测的最小值,实际应用中两根线都要接对绕组。
    • Data sheet 4313.

    Irms 0.67 A is the thermal limit - a 40 °C temperature rise at 85 °C ambient. With 0.33 ohm of DCR the winding loss at that current is 0.15 W. CMS2 is the mid-size CMS footprint

    Frequently Asked Questions

    Does it affect my signal?
    Only through DCR and the small amount of leakage inductance. The differential signal is not filtered by design.

    What impedance should I pick?
    The one that gives the attenuation you need at the noise frequency of your circuit, then check that the DCR is acceptable on the signal.

    What impedance should I pick?
    The one that gives the attenuation you need at the noise frequency of your circuit, then check that the DCR is acceptable on the signal.

    Design note: pick the choke by impedance at the noise
    frequency, then confirm DCR and rated current against the signal or the rail.

    Mechanical Dimensions

    eaton-cms-common-mode-inductors-surface-mount-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products