Eaton CMS3-4-R Common-Mode Noise Suppressor, 88 uH
Eaton CMS3-4-R Common-Mode Noise Suppressor, 88 uH

Eaton CMS3-4-R Common-Mode Noise Suppressor, 88 uH

Share
Eaton CMS3-4-R: 88 uH common-mode inductor, 3.95 A Irms, 0.01 ohm DCR, surface mount.
    • Product Details
    • Download

    Eaton CMS3-4-R Common-Mode Noise Suppressor, 88 uH

    CMS3-4-R: common-mode choke, OCL 88 uH minimum, 3.95 A Irms, leakage 0.85 uH.

    Electrical Specifications

    ParameterValue
    Orderable part numberCMS3-4-R
    Open circuit inductance (OCL)88 uH minimum, (1-2) & (4-3)
    I rms (max)3.95 A
    DCR typical @ 20 °C (1-2)0.01 ohm
    DCR typical @ 20 °C (4-3)0.01 ohm
    Leakage inductance typ0.85 uH
    Interwinding capacitance typ3.5 pF
    PackageCMS series, surface mount
    Operating temperature160 °C maximum
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Differential mode is not affected in theory, but DCR is real: every milliohm is a voltage drop and a bit of heat in the signal path, and on a low-voltage rail that matters.

    For a DC-DC output filter this is the part that decides whether the noise stays inside the conducted limits, and how much margin the design keeps at the top of the load step. 88 uH is the working middle of the CMS range: enough inductance to hold down the ripple on a rail, small enough that the 3.95 A Irms rating is not the thing limiting the design.

    Where This Series Fits

    CMS 是贴片共模电感,CMS1 / CMS2 / CMS3 三个尺寸系列,4.5 uH 到 1310 uH。

    • Typical use: 开关电源输出滤波、DC-DC 共模抑制、EMI 整改.
    • CMS 的 OCL 是在 (1-2) 与 (4-3) 两组绕组上测的最小值,实际应用中两根线都要接对绕组。
    • Data sheet 4313.

    The 88 uH of common-mode inductance is what blocks the noise; the 0.85 uH of leakage inductance is what gets past, and the 3.5 pF of interwinding capacitance is what couples across the windings at high frequency. CMS3 is the largest CMS footprint, with the lowest DCR of the three

    Frequently Asked Questions

    Is this part RoHS compliant?
    Yes - the -R suffix denotes the RoHS build.

    Is this part RoHS compliant?
    Yes - the -R suffix denotes the RoHS build.

    Why are there two DCR values?
    The CMS series specifies each winding separately, measured between (1-2) and between (4-3).

    Design note: pick the choke by impedance at the noise
    frequency, then confirm DCR and rated current against the signal or the rail.

    Mechanical Dimensions

    eaton-cms-common-mode-inductors-surface-mount-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products