Eaton DRQ125-470-R Dual Winding Shielded Inductor, 47 uH uH
Eaton DRQ125-470-R Dual Winding Shielded Inductor, 47 uH uH

Eaton DRQ125-470-R Dual Winding Shielded Inductor, 47 uH uH

Share
Eaton DRQ125-470-R: Dual Winding Shielded Drum Core Inductor, 47 uH, 2.71 A, DCR 74 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-470-R Dual Winding Shielded Inductor, 47 uH uH

    DRQ125-470-R at a glance: dual-winding shielded drum core, 47 uH per winding, 2.71 A, DCR 74 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ125-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)47.5 uH
    Irms (40 °C rise)2.71 A
    Isat3.24 A
    DCR typical @ 20 °C74 mOhm
    Volt-microsecond rating32.3 V-us
    Series connection190 uH, 1.35 A
    Parallel connection47 uH, 2.71 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A dual-winding drum core is a single core with two identical windings. Left uncoupled it is two chokes in one package; coupled, it becomes a 1:1 transformer for a SEPIC or a flyback, or a ripple-cancelling element in a multiphase converter.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Design Notes

    Choose 47 uH when the ripple target is in the middle of the design window: the DCR stays at 74 mOhm and the saturation limit at 3.24 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products