Eaton DRQ125-8R2-R Shielded Coupled Inductor 8.2 uH 5.54 A
Eaton DRQ125-8R2-R Shielded Coupled Inductor 8.2 uH 5.54 A

Eaton DRQ125-8R2-R Shielded Coupled Inductor 8.2 uH 5.54 A

Share
Eaton DRQ125-8R2-R: Dual Winding Shielded Drum Core Inductor, 8.2 uH, 5.54 A, DCR 17.6 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-8R2-R Shielded Coupled Inductor 8.2 uH 5.54 A

    DRQ125-8R2-R at a glance: dual-winding shielded drum core, 8.2 uH per winding, 5.54 A, DCR 17.6 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ125-8R2-R
    Rated inductance8.2 uH ±20%
    Open circuit inductance (OCL)8.05 uH
    Irms (40 °C rise)5.54 A
    Isat7.86 A
    DCR typical @ 20 °C17.6 mOhm
    Volt-microsecond rating13.3 V-us
    Series connection32.2 uH, 2.77 A
    Parallel connection8.2 uH, 5.54 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A dual-winding drum core is a single core with two identical windings. Left uncoupled it is two chokes in one package; coupled, it becomes a 1:1 transformer for a SEPIC or a flyback, or a ripple-cancelling element in a multiphase converter.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Sizing It Into a Design

    Choose 8.2 uH when the ripple target is in the middle of the design window: the DCR stays at 17.6 mOhm and the saturation limit at 7.86 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products