Eaton DRQ127-2R2-R - Dual Winding 2.2 uH Power Inductor
Eaton DRQ127-2R2-R - Dual Winding 2.2 uH Power Inductor

Eaton DRQ127-2R2-R - Dual Winding 2.2 uH Power Inductor

Share
Eaton DRQ127-2R2-R: Dual Winding Shielded Drum Core Inductor, 2.2 uH, 12.5 A, DCR 3.73 mOhm.
    • Product Details
    • Download

    Eaton DRQ127-2R2-R - Dual Winding 2.2 uH Power Inductor

    DRQ127-2R2-R at a glance: dual-winding shielded drum core, 2.2 uH per winding, 12.5 A, DCR 3.73 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ127-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.03 uH
    Irms (40 °C rise)12.5 A
    Isat25.5 A
    DCR typical @ 20 °C3.73 mOhm
    Volt-microsecond rating7.7 V-us
    Series connection8.11 uH, 6.23 A
    Parallel connection2.2 uH, 12.5 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DRQ127 is the tallest dual-winding DRQ at 8.0 mm and the highest-current part in the family, up to 56 A peak in parallel mode. Two windings, one core, and the option to use it as a transformer.

    • Typical applications: High current DC-DC, server power, SEPIC and flyback, battery systems, filter chokes.
    • The parallel rating is not double the single-winding rating of the same size - check both windings' DCR and the thermal path before assuming it.
    • Data sheet DS4311.

    Sizing and Layout Notes

    2.2 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products