Eaton DRQ73-102-R - Dual Winding 1000 uH Power Inductor
Eaton DRQ73-102-R - Dual Winding 1000 uH Power Inductor

Eaton DRQ73-102-R - Dual Winding 1000 uH Power Inductor

Share
Eaton DRQ73-102-R: Dual Winding Shielded Drum Core Inductor, 1000 uH, 0.26 A, DCR 4.34 ohm.
    • Product Details
    • Download

    Eaton DRQ73-102-R - Dual Winding 1000 uH Power Inductor

    DRQ73-102-R at a glance: dual-winding shielded drum core, 1000 uH per winding, 0.26 A, DCR 4340 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ73-102-R
    Rated inductance1000 uH ±20%
    Open circuit inductance (OCL)995 uH
    Irms (40 °C rise)0.26 A
    Isat0.25 A
    DCR typical @ 20 °C4340 mOhm
    Volt-microsecond rating113 V-us
    Series connection3980 uH, 0.13 A
    Parallel connection1000 uH, 0.26 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Sizing It Into a Design

    At 1000 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 4340 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products