Eaton DRQ73-220-R - Dual Winding 22 uH Power Inductor
Eaton DRQ73-220-R - Dual Winding 22 uH Power Inductor

Eaton DRQ73-220-R - Dual Winding 22 uH Power Inductor

Share
Eaton DRQ73-220-R: Dual Winding Shielded Drum Core Inductor, 22 uH, 1.62 A, DCR 107 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-220-R - Dual Winding 22 uH Power Inductor

    DRQ73-220-R at a glance: dual-winding shielded drum core, 22 uH per winding, 1.62 A, DCR 107 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ73-220-R
    Rated inductance22 uH ±20%
    Open circuit inductance (OCL)22.6 uH
    Irms (40 °C rise)1.62 A
    Isat1.67 A
    DCR typical @ 20 °C107 mOhm
    Volt-microsecond rating17 V-us
    Series connection90.6 uH, 0.81 A
    Parallel connection22 uH, 1.62 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Sizing and Layout Notes

    Choose 22 uH when the ripple target is in the middle of the design window: the DCR stays at 107 mOhm and the saturation limit at 1.67 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message