Eaton DRQ73-330-R Dual Winding Shielded Inductor, 33 uH uH
Eaton DRQ73-330-R Dual Winding Shielded Inductor, 33 uH uH

Eaton DRQ73-330-R Dual Winding Shielded Inductor, 33 uH uH

Share
Eaton DRQ73-330-R: Dual Winding Shielded Drum Core Inductor, 33 uH, 1.31 A, DCR 166 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-330-R Dual Winding Shielded Inductor, 33 uH uH

    DRQ73-330-R at a glance: dual-winding shielded drum core, 33 uH per winding, 1.31 A, DCR 166 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ73-330-R
    Rated inductance33 uH ±20%
    Open circuit inductance (OCL)34.4 uH
    Irms (40 °C rise)1.31 A
    Isat1.35 A
    DCR typical @ 20 °C166 mOhm
    Volt-microsecond rating21 V-us
    Series connection138 uH, 0.65 A
    Parallel connection33 uH, 1.31 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A dual-winding drum core is a single core with two identical windings. Left uncoupled it is two chokes in one package; coupled, it becomes a 1:1 transformer for a SEPIC or a flyback, or a ripple-cancelling element in a multiphase converter.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Sizing It Into a Design

    33 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message