Eaton DRQ73-680-R 68 uH Coupled Drum Core Inductor
Eaton DRQ73-680-R 68 uH Coupled Drum Core Inductor

Eaton DRQ73-680-R 68 uH Coupled Drum Core Inductor

Share
Eaton DRQ73-680-R: Dual Winding Shielded Drum Core Inductor, 68 uH, 0.89 A, DCR 358 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-680-R 68 uH Coupled Drum Core Inductor

    DRQ73-680-R at a glance: dual-winding shielded drum core, 68 uH per winding, 0.89 A, DCR 358 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ73-680-R
    Rated inductance68 uH ±20%
    Open circuit inductance (OCL)68.9 uH
    Irms (40 °C rise)0.89 A
    Isat0.96 A
    DCR typical @ 20 °C358 mOhm
    Volt-microsecond rating29.7 V-us
    Series connection276 uH, 0.44 A
    Parallel connection68 uH, 0.89 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Sizing It Into a Design

    At 68 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 358 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products