Eaton DRQ73-6R8-R Shielded Coupled Inductor 6.8 uH 2.55 A
Eaton DRQ73-6R8-R Shielded Coupled Inductor 6.8 uH 2.55 A

Eaton DRQ73-6R8-R Shielded Coupled Inductor 6.8 uH 2.55 A

Share
Eaton DRQ73-6R8-R: Dual Winding Shielded Drum Core Inductor, 6.8 uH, 2.55 A, DCR 43.5 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-6R8-R Shielded Coupled Inductor 6.8 uH 2.55 A

    DRQ73-6R8-R at a glance: dual-winding shielded drum core, 6.8 uH per winding, 2.55 A, DCR 43.5 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ73-6R8-R
    Rated inductance6.8 uH ±20%
    Open circuit inductance (OCL)6.48 uH
    Irms (40 °C rise)2.55 A
    Isat3.12 A
    DCR typical @ 20 °C43.5 mOhm
    Volt-microsecond rating9.11 V-us
    Series connection25.9 uH, 1.28 A
    Parallel connection6.8 uH, 2.55 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Design Notes

    At 6.8 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 43.5 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products