Eaton DRQ74-101-R 1:1 Coupled Drum Core, 100 uH
Eaton DRQ74-101-R 1:1 Coupled Drum Core, 100 uH

Eaton DRQ74-101-R 1:1 Coupled Drum Core, 100 uH

Share
Eaton DRQ74-101-R: Dual Winding Shielded Drum Core Inductor, 100 uH, 0.86 A, DCR 383 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-101-R 1:1 Coupled Drum Core, 100 uH

    DRQ74-101-R at a glance: dual-winding shielded drum core, 100 uH per winding, 0.86 A, DCR 383 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ74-101-R
    Rated inductance100 uH ±20%
    Open circuit inductance (OCL)102 uH
    Irms (40 °C rise)0.86 A
    Isat0.99 A
    DCR typical @ 20 °C383 mOhm
    Volt-microsecond rating31.8 V-us
    Series connection406 uH, 0.43 A
    Parallel connection100 uH, 0.86 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Design Notes

    100 uH sits in the middle of the range, and the trade at that point is explicit: 383 mOhm of DCR against 0.99 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products