Eaton DRQ74-150-R 15 uH Coupled Drum Core Inductor
Eaton DRQ74-150-R 15 uH Coupled Drum Core Inductor

Eaton DRQ74-150-R 15 uH Coupled Drum Core Inductor

Share
Eaton DRQ74-150-R: Dual Winding Shielded Drum Core Inductor, 15 uH, 2.11 A, DCR 63.7 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-150-R 15 uH Coupled Drum Core Inductor

    DRQ74-150-R at a glance: dual-winding shielded drum core, 15 uH per winding, 2.11 A, DCR 63.7 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ74-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)16.1 uH
    Irms (40 °C rise)2.11 A
    Isat2.48 A
    DCR typical @ 20 °C63.7 mOhm
    Volt-microsecond rating12.7 V-us
    Series connection64.4 uH, 1.05 A
    Parallel connection15 uH, 2.11 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Sizing and Layout Notes

    Choose 15 uH when the ripple target is in the middle of the design window: the DCR stays at 63.7 mOhm and the saturation limit at 2.48 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products