Eaton DRQ74-470-R 47 uH Coupled Drum Core Inductor
Eaton DRQ74-470-R 47 uH Coupled Drum Core Inductor

Eaton DRQ74-470-R 47 uH Coupled Drum Core Inductor

Share
Eaton DRQ74-470-R: Dual Winding Shielded Drum Core Inductor, 47 uH, 1.15 A, DCR 216 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-470-R 47 uH Coupled Drum Core Inductor

    DRQ74-470-R at a glance: dual-winding shielded drum core, 47 uH per winding, 1.15 A, DCR 216 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ74-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)49.6 uH
    Irms (40 °C rise)1.15 A
    Isat1.41 A
    DCR typical @ 20 °C216 mOhm
    Volt-microsecond rating22.2 V-us
    Series connection199 uH, 0.57 A
    Parallel connection47 uH, 1.15 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A dual-winding drum core is a single core with two identical windings. Left uncoupled it is two chokes in one package; coupled, it becomes a 1:1 transformer for a SEPIC or a flyback, or a ripple-cancelling element in a multiphase converter.

    Series mode is often mistaken for a way to get more current. It is the opposite - four times the inductance, half the saturation current, twice the DCR. Use it when you need inductance, not when you need amps.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Putting It to Work

    Choose 47 uH when the ripple target is in the middle of the design window: the DCR stays at 216 mOhm and the saturation limit at 1.41 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products