Eaton DRQ74-6R8-R 6.8 uH Coupled Drum Core Inductor
Eaton DRQ74-6R8-R 6.8 uH Coupled Drum Core Inductor

Eaton DRQ74-6R8-R 6.8 uH Coupled Drum Core Inductor

Share
Eaton DRQ74-6R8-R: Dual Winding Shielded Drum Core Inductor, 6.8 uH, 2.6 A, DCR 41.8 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-6R8-R 6.8 uH Coupled Drum Core Inductor

    DRQ74-6R8-R at a glance: dual-winding shielded drum core, 6.8 uH per winding, 2.6 A, DCR 41.8 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ74-6R8-R
    Rated inductance6.8 uH ±20%
    Open circuit inductance (OCL)7.34 uH
    Irms (40 °C rise)2.6 A
    Isat3.67 A
    DCR typical @ 20 °C41.8 mOhm
    Volt-microsecond rating8.55 V-us
    Series connection29.4 uH, 1.3 A
    Parallel connection6.8 uH, 2.6 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Design Notes

    Choose 6.8 uH when the ripple target is in the middle of the design window: the DCR stays at 41.8 mOhm and the saturation limit at 3.67 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products