Eaton DRQ74-821-R Shielded Coupled Inductor 820 uH 0.31 A
Eaton DRQ74-821-R Shielded Coupled Inductor 820 uH 0.31 A

Eaton DRQ74-821-R Shielded Coupled Inductor 820 uH 0.31 A

Share
Eaton DRQ74-821-R: Dual Winding Shielded Drum Core Inductor, 820 uH, 0.31 A, DCR 2.93 ohm.
    • Product Details
    • Download

    Eaton DRQ74-821-R Shielded Coupled Inductor 820 uH 0.31 A

    DRQ74-821-R at a glance: dual-winding shielded drum core, 820 uH per winding, 0.31 A, DCR 2930 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ74-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)813 uH
    Irms (40 °C rise)0.31 A
    Isat0.35 A
    DCR typical @ 20 °C2930 mOhm
    Volt-microsecond rating89.9 V-us
    Series connection3251 uH, 0.16 A
    Parallel connection820 uH, 0.31 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Sizing and Layout Notes

    Choose 820 uH when the ripple target is in the middle of the design window: the DCR stays at 2930 mOhm and the saturation limit at 0.35 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message