Eaton ECMT1V1714H-150-R Common-Mode Inductor, 15 mH THT
Eaton ECMT1V1714H-150-R Common-Mode Inductor, 15 mH THT

Eaton ECMT1V1714H-150-R Common-Mode Inductor, 15 mH THT

Share
Eaton ECMT1V1714H-150-R: Through-Hole Common-Mode Inductor, 15 mH per winding, 1 A.
    • Product Details
    • Download

    Eaton ECMT1V1714H-150-R Common-Mode Inductor, 15 mH THT

    ECMT1V1714H-150-R at a glance: through-hole common-mode inductor, 15 mH per winding, 1 A per winding, isolation 1500/1000 Vac.

    Electrical Specifications

    ParameterValue
    Orderable part numberECMT1V1714H-150-R
    OCL minimum, (1-2) & (4-3)15 mH
    DCR maximum @ +25 °C, (1-2) & (4-3)0.6 Ohm
    Irms per winding, (1-4) short1 A
    SRF minimum408 kHz
    Hi-pot, coil-to-core1500 Vac, 2 s, 5 mA
    Hi-pot, coil-to-coil1000 Vac, 2 s, 5 mA
    Insulation resistance minimum100 MOhm
    Rated voltage250 Vac
    Packagethrough-hole, closed magnetic path, rated 250 Vac
    MountingThrough-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Mechanical Drawing

    ECMT1V1714H-150-R mechanical dimensions and pad layout

    Drawings from the Eaton data sheet: mechanical outline with rated mm dimensions, recommended PCB pad layout, and winding schematic. Tolerances and pad tolerances are stated on the drawing itself.

    Reading the Data Sheet

    Two windings, one closed core, and isolation ratings measured both coil-to-coil and coil-to-core: this is a common-mode inductor built for industrial IoT equipment, motion controls and renewable energy products rather than for consumer boards.

    The two winding sections are specified separately because a mismatch turns common-mode noise into differential noise. The Hi-pot figures are quoted coil-to-core and coil-to-coil - both are functional isolation ratings, and the 250 Vac rated voltage governs what lines the part may sit between.

    Irms is rated per winding with the section short-circuited, which is the harshest thermal case for a common-mode inductor: the whole winding carries the current with no cancellation to help.

    Copper loss is the efficiency floor. 600 mOhm at 25 °C rises about 30% by 100 °C, so the hot-corner budget should use the maximum column, not the typical.

    Series Positioning

    ECMT is the through-hole common-mode family for industrial power equipment - motion controls, power supplies, solar and wind inverters, chargers - where high isolation and a robust soldered filter point matter more than board area.

    • Typical applications: industrial IoT equipment, motion controls, power supplies, battery backup, solar/wind inverters and charger controllers, medical equipment.
    • Wave-soldered construction: keep the coil-to-core and coil-to-coil Hi-pot ratings in mind when the two winding sections sit on different circuit domains.
    • Data sheet ELX1092; footprint through-hole, closed magnetic path, rated 250 Vac.

    Sizing It Into a Design

    Frequently Asked Questions

    Why are there two OCL columns?
    The two winding sections are measured separately, (1-2) and (4-3). Mismatch between them turns common-mode noise into differential noise.

    What are the two Hi-pot ratings?
    Coil-to-core and coil-to-coil isolation, each tested for 2 seconds at 5 mA. They are functional isolation ratings for circuit architecture, not safety barriers.

    Can I use it on a DC line?
    The rated voltage is 250 Vac for the winding insulation; large unbalanced DC on the lines biases the core and reduces the impedance. Keep the lines balanced.

    Design note: the SRF column is a minimum; the choke stops filtering above it. Match the part to the noise band, not just to the inductance.

    Mechanical Dimensions

    eaton-ecmt1v17-common-mode-inductor-tht-data-sheet-elx1092-en mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message