Eaton ECMT1V2017H-200-R Through-Hole Common-Mode Inductor 20 mH
Eaton ECMT1V2017H-200-R Through-Hole Common-Mode Inductor 20 mH

Eaton ECMT1V2017H-200-R Through-Hole Common-Mode Inductor 20 mH

Share
Eaton ECMT1V2017H-200-R: Through-Hole Common-Mode Inductor, 20 mH per winding, 1 A.
    • Product Details
    • Download

    Eaton ECMT1V2017H-200-R Through-Hole Common-Mode Inductor 20 mH

    ECMT1V2017H-200-R at a glance: through-hole common-mode inductor, 20 mH per winding, 1 A per winding, isolation 1500/1000 Vac.

    Electrical Specifications

    ParameterValue
    Orderable part numberECMT1V2017H-200-R
    OCL minimum, (1-2) & (4-3)20 mH
    DCR maximum @ +25 °C, (1-2) & (4-3)0.55 Ohm
    Irms per winding, (1-4) short1 A
    SRF minimum245 kHz
    Hi-pot, coil-to-core1500 Vac, 2 s, 5 mA
    Hi-pot, coil-to-coil1000 Vac, 2 s, 5 mA
    Insulation resistance minimum100 MOhm
    Rated voltage250 Vac
    Packagethrough-hole, closed magnetic path, rated 250 Vac
    MountingThrough-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Outline Drawing

    ECMT1V2017H-200-R mechanical dimensions and pad layout

    Drawings from the Eaton data sheet: mechanical outline with rated mm dimensions, recommended PCB pad layout, and winding schematic. Tolerances and pad tolerances are stated on the drawing itself.

    How to Read These Ratings

    A through-hole common-mode inductor with a closed magnetic path: the two independent winding sections share a ferrite core, differential current cancels, and common-mode noise sees the full inductance. Built for equipment where the filter point is a soldered, high-isolation component rather than a replaceable cartridge.

    The two winding sections are specified separately because a mismatch turns common-mode noise into differential noise. The Hi-pot figures are quoted coil-to-core and coil-to-coil - both are functional isolation ratings, and the 250 Vac rated voltage governs what lines the part may sit between.

    Irms is rated per winding with the section short-circuited, which is the harshest thermal case for a common-mode inductor: the whole winding carries the current with no cancellation to help.

    The typical and the maximum DCR are both quoted for a reason: production spread. A loss budget that has to hold across a build uses 550 mOhm as the optimistic case and plans against the maximum.

    What This Family Is For

    ECMT is the through-hole common-mode family for industrial power equipment - motion controls, power supplies, solar and wind inverters, chargers - where high isolation and a robust soldered filter point matter more than board area.

    • Typical applications: industrial IoT equipment, motion controls, power supplies, battery backup, solar/wind inverters and charger controllers, medical equipment.
    • Wave-soldered construction: keep the coil-to-core and coil-to-coil Hi-pot ratings in mind when the two winding sections sit on different circuit domains.
    • Data sheet ELX1093; footprint through-hole, closed magnetic path, rated 250 Vac.

    Putting It to Work

    Frequently Asked Questions

    What are the two Hi-pot ratings?
    Coil-to-core and coil-to-coil isolation, each tested for 2 seconds at 5 mA. They are functional isolation ratings for circuit architecture, not safety barriers.

    Can I use it on a DC line?
    The rated voltage is 250 Vac for the winding insulation; large unbalanced DC on the lines biases the core and reduces the impedance. Keep the lines balanced.

    Can I use it on a DC line?
    The rated voltage is 250 Vac for the winding insulation; large unbalanced DC on the lines biases the core and reduces the impedance. Keep the lines balanced.

    Design note: the SRF column is a minimum; the choke stops filtering above it. Match the part to the noise band, not just to the inductance.

    Mechanical Dimensions

    eaton-ecmt1v20-common-mode-inductor-tht-data-sheet-elx1093-en mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products