Eaton FP0404R1-R022-R 22 nH Power Inductor, 40 A
Eaton FP0404R1-R022-R 22 nH Power Inductor, 40 A

Eaton FP0404R1-R022-R 22 nH Power Inductor, 40 A

Share
pEaton FP0404R1-R022-R: 22 nH high frequency, high current power inductor, 40 A Irms, 40 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm package./p
    • Product Details
    • Download

    FP0404R1-R022-R at a glance: 22 nH high frequency, high current power inductor, 40 A Irms, 40 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.

    Eaton FP0404R1-R022-R High frequency, high current power inductors

    The FP0404R1-R022-R is a 4.0 x 4.0 mm high frequency, high current power inductor from Eaton, rated 40 A Irms at 22 nH and 0.32 mOhm typical DCR. It is a surface-mount part 3.0 mm or 4.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP0404R1-R022-R
    Inductance, OCL (0 Adc)22 nH
    Inductance, FLL (minimum)15 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)40 A
    Isat2 (20% roll-off @ +100 °C)34 A
    Isat3 (20% roll-off @ +125 °C)32 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)2,351
    Package4.0 x 4.0 mm, 3.0 mm / 4.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 22 nH. Put Isat1 through it and the figure falls to 15 nH, about 32% lower, because the ferrite is partly saturated. Ripple calculations belong on the 22 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 40 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 40 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.32 mOhm that is roughly 512 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 2,351 and a ripple of 12 A the core sees roughly 62.1 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 22 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 6 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 22 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0404R1-R022-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message