
FP0404R1-R065-R at a glance: 65 nH high frequency, high current power inductor, 40 A Irms, 24 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.
FP0404R1-R065-R is one of Eaton's high frequency, high current power inductor series, 4.0 x 4.0 mm with a 3.0 mm or 4.0 mm tall profile. Electrically it offers 65 nH at 40 A Irms and 0.32 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP0404R1-R065-R |
| Inductance, OCL (0 Adc) | 65 nH |
| Inductance, FLL (minimum) | 44 nH |
| Irms (40 °C rise, no core loss) | 40 A |
| Isat (20% roll-off @ +25 °C) | 24 A |
| Isat2 (20% roll-off @ +100 °C) | 22 A |
| Isat3 (20% roll-off @ +125 °C) | 20 A |
| DCR typical @ +20 °C | 0.32 mOhm |
| K-factor (Bp-p = K x L x dI) | 2,248 |
| Package | 4.0 x 4.0 mm, 3.0 mm / 4.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 65 nH. Put Isat1 through it and the figure falls to 44 nH, about 32% lower, because the ferrite is partly saturated. Ripple calculations belong on the 65 nH number; loop stability and worst-case current belong on the lower one.
Saturation is quoted as 20% roll-off at 24 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
The 512 mW dissipated at 40 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Flux swing follows Bp-p = K x L x dI. With K = 2,248 and a ripple of 7.2 A the core sees roughly 105.2 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 65 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it part 2 of 6 when the data sheet is sorted by inductance.
The order of checks that works: compute ripple from 65 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd