Eaton FP0404R1-R080-R High Current Inductor, 80 nH 0.32 mOhm
Eaton FP0404R1-R080-R High Current Inductor, 80 nH 0.32 mOhm

Eaton FP0404R1-R080-R High Current Inductor, 80 nH 0.32 mOhm

Share
pEaton FP0404R1-R080-R: 80 nH high frequency, high current power inductor, 40 A Irms, 19.5 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm package./p
    • Product Details
    • Download

    FP0404R1-R080-R at a glance: 80 nH high frequency, high current power inductor, 40 A Irms, 19.5 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.

    Eaton FP0404R1-R080-R High frequency, high current power inductors

    Eaton builds the FP0404R1-R080-R as a high frequency, high current power inductor for 4.0 x 4.0 mm footprints. At 80 nH and 40 A Irms with 0.32 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 4.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP0404R1-R080-R
    Inductance, OCL (0 Adc)80 nH
    Inductance, FLL (minimum)54 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)19.5 A
    Isat2 (20% roll-off @ +100 °C)18 A
    Isat3 (20% roll-off @ +125 °C)16 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)2,248
    Package4.0 x 4.0 mm, 3.0 mm / 4.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    80 nH open-circuit, 54 nH at full load: that is a 32% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 19.5 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 512 mW (40 A squared times 0.32 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 2,248 turns ripple into flux: a peak-to-peak swing of 5.85 A gives about 105.2 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 80 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 3 of 6 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 80 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.32 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0404R1-R080-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products