
FP0404R1-R170-R at a glance: 170 nH high frequency, high current power inductor, 40 A Irms, 9 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.
Eaton FP0404R1-R170-R is a high frequency, high current power inductor in a 4.0 x 4.0 mm surface-mount package. It carries 170 nH of open-circuit inductance with 40 A Irms and a typical DCR of 0.32 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 3.0 mm or 4.0 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP0404R1-R170-R |
| Inductance, OCL (0 Adc) | 170 nH |
| Inductance, FLL (minimum) | 116 nH |
| Irms (40 °C rise, no core loss) | 40 A |
| Isat (20% roll-off @ +25 °C) | 9 A |
| Isat2 (20% roll-off @ +100 °C) | 7.8 A |
| Isat3 (20% roll-off @ +125 °C) | 7.6 A |
| DCR typical @ +20 °C | 0.32 mOhm |
| K-factor (Bp-p = K x L x dI) | 2,248 |
| Package | 4.0 x 4.0 mm, 3.0 mm / 4.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 170 nH. Put Isat1 through it and the figure falls to 116 nH, about 32% lower, because the ferrite is partly saturated. Ripple calculations belong on the 170 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 9 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 512 mW dissipated at 40 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The K-factor of 2,248 turns ripple into flux: a peak-to-peak swing of 2.7 A gives about 103.2 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 170 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it the highest inductance of the 6 parts in this data sheet.
The order of checks that works: compute ripple from 170 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd