Eaton FP0507V1-R050-R High Current Inductor, 50 nH 0.47 mOhm
Eaton FP0507V1-R050-R High Current Inductor, 50 nH 0.47 mOhm

Eaton FP0507V1-R050-R High Current Inductor, 50 nH 0.47 mOhm

Share
pEaton FP0507V1-R050-R: 50 nH high frequency, high current power inductor, 35 A Irms, 80 A Isat, DCR 0.47 mOhm, 5.2 x 5.0 mm package./p
    • Product Details
    • Download

    FP0507V1-R050-R at a glance: 50 nH high frequency, high current power inductor, 35 A Irms, 80 A Isat, DCR 0.47 mOhm, 5.2 x 5.0 mm body, 6.6 mm tall.

    Eaton FP0507V1-R050-R High frequency, high current power inductors

    Eaton FP0507V1-R050-R is a high frequency, high current power inductor in a 5.2 x 5.0 mm surface-mount package. It carries 50 nH of open-circuit inductance with 35 A Irms and a typical DCR of 0.47 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 6.6 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP0507V1-R050-R
    Inductance, OCL (0 Adc)50 nH
    Inductance, FLL (minimum)36 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +100 °C)70 A
    Isat3 (20% roll-off @ +125 °C)66 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)886
    Package5.2 x 5.0 mm, 6.6 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 50 nH is measured with no DC in the winding, 36 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 80 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 576 mW dissipated at 35 A through 0.47 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 886 and a ripple of 24 A the core sees roughly 106.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 5.2 x 5.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 50 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high­ power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 50 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.47 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0507V1-R050-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products