
FP0705R1-R07-R at a glance: 72 nH high frequency, high current power inductor, 43 A Irms, 65 A Isat, DCR 0.25 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.
Eaton FP0705R1-R07-R is a high frequency, high current power inductor in a 7.0 x 7.0 mm surface-mount package. It carries 72 nH of open-circuit inductance with 43 A Irms and a typical DCR of 0.25 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.95 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP0705R1-R07-R |
| Inductance, OCL (0 Adc) | 72 nH |
| Inductance, FLL (minimum) | 51 nH |
| Irms (40 °C rise, no core loss) | 43 A |
| Isat (20% roll-off @ +25 °C) | 65 A |
| Isat2 (20% roll-off @ +125 °C) | 50 A |
| DCR typical @ +20 °C | 0.25 mOhm |
| K-factor (Bp-p = K x L x dI) | 826 |
| Package | 7.0 x 7.0 mm, 4.95 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 72 nH. Put Isat1 through it and the figure falls to 51 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 72 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 65 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 43 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.25 mOhm that is roughly 462 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The K-factor of 826 turns ripple into flux: a peak-to-peak swing of 19.5 A gives about 116 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 72 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it the lowest inductance of the 18 parts in this data sheet, and it shares the lowest DCR here at 0.25 mOhm, Irms of 43 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 72 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.25 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd