Eaton FP0705R1-R10-R 105 nH Power Inductor, 43 A
Eaton FP0705R1-R10-R 105 nH Power Inductor, 43 A

Eaton FP0705R1-R10-R 105 nH Power Inductor, 43 A

Share
pEaton FP0705R1-R10-R: 105 nH high frequency, high current power inductor, 43 A Irms, 44 A Isat, DCR 0.25 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R1-R10-R at a glance: 105 nH high frequency, high current power inductor, 43 A Irms, 44 A Isat, DCR 0.25 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R1-R10-R High frequency, high current power inductors

    Eaton builds the FP0705R1-R10-R as a high frequency, high current power inductor for 7.0 x 7.0 mm footprints. At 105 nH and 43 A Irms with 0.25 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0705R1-R10-R
    Inductance, OCL (0 Adc)105 nH
    Inductance, FLL (minimum)78 nH
    Irms (40 °C rise, no core loss)43 A
    Isat (20% roll-off @ +25 °C)44 A
    Isat2 (20% roll-off @ +125 °C)34 A
    DCR typical @ +20 °C0.25 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    105 nH open-circuit, 78 nH at full load: that is a 26% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 44 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 462 mW (43 A squared times 0.25 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 826 and a ripple of 13.2 A the core sees roughly 114.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 105 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 18 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.25 mOhm, Irms of 43 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 105 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.25 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0705R1-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message