
FP0705R1-R22-R at a glance: 226 nH high frequency, high current power inductor, 43 A Irms, 20 A Isat, DCR 0.25 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.
The FP0705R1-R22-R is a 7.0 x 7.0 mm high frequency, high current power inductor from Eaton, rated 43 A Irms at 226 nH and 0.25 mOhm typical DCR. It is a surface-mount part 4.95 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP0705R1-R22-R |
| Inductance, OCL (0 Adc) | 226 nH |
| Inductance, FLL (minimum) | 159 nH |
| Irms (40 °C rise, no core loss) | 43 A |
| Isat (20% roll-off @ +25 °C) | 20 A |
| Isat2 (20% roll-off @ +125 °C) | 16 A |
| DCR typical @ +20 °C | 0.25 mOhm |
| K-factor (Bp-p = K x L x dI) | 826 |
| Package | 7.0 x 7.0 mm, 4.95 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
226 nH open-circuit, 159 nH at full load: that is a 30% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Saturation is quoted as 20% roll-off at 20 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Copper loss at the rated current works out at about 462 mW (43 A squared times 0.25 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 112 mT for a 6 A ripple (K = 826). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 226 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 16 of 18 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.25 mOhm, Irms of 43 A is the top of the family.
The order of checks that works: compute ripple from 226 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.25 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd