Eaton FP0705R2-R07-R 72 nH Power Inductor, 38 A
Eaton FP0705R2-R07-R 72 nH Power Inductor, 38 A

Eaton FP0705R2-R07-R 72 nH Power Inductor, 38 A

Share
pEaton FP0705R2-R07-R: 72 nH high frequency, high current power inductor, 38 A Irms, 65 A Isat, DCR 0.32 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R2-R07-R at a glance: 72 nH high frequency, high current power inductor, 38 A Irms, 65 A Isat, DCR 0.32 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R2-R07-R High frequency, high current power inductors

    The FP0705R2-R07-R is a 7.0 x 7.0 mm high frequency, high current power inductor from Eaton, rated 38 A Irms at 72 nH and 0.32 mOhm typical DCR. It is a surface-mount part 4.95 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP0705R2-R07-R
    Inductance, OCL (0 Adc)72 nH
    Inductance, FLL (minimum)51 nH
    Irms (40 °C rise, no core loss)38 A
    Isat (20% roll-off @ +25 °C)65 A
    Isat2 (20% roll-off @ +125 °C)50 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 72 nH. Put Isat1 through it and the figure falls to 51 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 72 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 65 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 462 mW dissipated at 38 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 826 and a ripple of 19.5 A the core sees roughly 116 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 72 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 18 parts in this data sheet, DCR sits between the 0.25 and 0.46 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 72 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R2-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products