Eaton FP0705R3-R07-R - 72 nH Shielded Power Inductor 7.0 x 7.0 mm
Eaton FP0705R3-R07-R - 72 nH Shielded Power Inductor 7.0 x 7.0 mm

Eaton FP0705R3-R07-R - 72 nH Shielded Power Inductor 7.0 x 7.0 mm

Share
pEaton FP0705R3-R07-R: 72 nH high frequency, high current power inductor, 32 A Irms, 65 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R3-R07-R at a glance: 72 nH high frequency, high current power inductor, 32 A Irms, 65 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R3-R07-R High frequency, high current power inductors

    Eaton builds the FP0705R3-R07-R as a high frequency, high current power inductor for 7.0 x 7.0 mm footprints. At 72 nH and 32 A Irms with 0.46 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP0705R3-R07-R
    Inductance, OCL (0 Adc)72 nH
    Inductance, FLL (minimum)51 nH
    Irms (40 °C rise, no core loss)32 A
    Isat (20% roll-off @ +25 °C)65 A
    Isat2 (20% roll-off @ +125 °C)50 A
    DCR typical @ +20 °C0.46 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 72 nH. Put Isat1 through it and the figure falls to 51 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 72 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 65 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 32 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.46 mOhm that is roughly 471 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 826 turns ripple into flux: a peak-to-peak swing of 19.5 A gives about 116 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 72 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 18 parts in this data sheet, with the highest DCR in the series at 0.46 mOhm, which is what the extra turns cost, Irms of 32 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 72 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.46 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R3-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products