
FP0707R1-R110-R at a glance: 110 nH high frequency, high current power inductor, 45 A Irms, 67 A Isat, DCR 0.3 mOhm, 7.2 x 7.2 mm body, 7.0 mm tall.
The FP0707R1-R110-R is a 7.2 x 7.2 mm high frequency, high current power inductor from Eaton, rated 45 A Irms at 110 nH and 0.3 mOhm typical DCR. It is a surface-mount part 7.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP0707R1-R110-R |
| Inductance, OCL (0 Adc) | 110 nH |
| Inductance, FLL (minimum) | 79 nH |
| Irms (40 °C rise, no core loss) | 45 A |
| Isat (20% roll-off @ +25 °C) | 67 A |
| Isat2 (20% roll-off @ +100 °C) | 55 A |
| Isat3 (20% roll-off @ +125 °C) | 51 A |
| DCR typical @ +20 °C | 0.3 mOhm |
| K-factor (Bp-p = K x L x dI) | 542 |
| Package | 7.2 x 7.2 mm, 7.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
110 nH open-circuit, 79 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
The first Isat column, 67 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Copper loss at the rated current works out at about 608 mW (45 A squared times 0.3 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 119.8 mT for a 20.1 A ripple (K = 542). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 7.2 x 7.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
Size the inductor on peak current first, not average. With 110 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.3 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd