Eaton FP0708R1-R07-R 44 A SMD Power Inductor, 72 nH
Eaton FP0708R1-R07-R 44 A SMD Power Inductor, 72 nH

Eaton FP0708R1-R07-R 44 A SMD Power Inductor, 72 nH

Share
pEaton FP0708R1-R07-R: 72 nH high frequency, high current power inductor, 44 A Irms, 90 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm package./p
    • Product Details
    • Download

    FP0708R1-R07-R at a glance: 72 nH high frequency, high current power inductor, 44 A Irms, 90 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm body, 7.2 mm tall.

    Eaton FP0708R1-R07-R High frequency, high current power inductors

    Eaton FP0708R1-R07-R is a high frequency, high current power inductor in a 7.0 x 8.5 mm surface-mount package. It carries 72 nH of open-circuit inductance with 44 A Irms and a typical DCR of 0.35 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.2 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0708R1-R07-R
    Inductance, OCL (0 Adc)72 nH
    Inductance, FLL (minimum)52 nH
    Irms (40 °C rise, no core loss)44 A
    Isat (20% roll-off @ +25 °C)90 A
    Isat2 (20% roll-off @ +125 °C)72 A
    DCR typical @ +20 °C0.35 mOhm
    K-factor (Bp-p = K x L x dI)557
    Package7.0 x 8.5 mm, 7.2 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 72 nH. Put Isat1 through it and the figure falls to 52 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 72 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 90 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 44 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.35 mOhm that is roughly 678 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 557 turns ripple into flux: a peak-to-peak swing of 27 A gives about 108.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 7.0 x 8.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 72 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 7 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 72 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.35 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0708R1-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products