Eaton FP0708R1-R09-R 90 nH 75 A Saturation Inductor
Eaton FP0708R1-R09-R 90 nH 75 A Saturation Inductor

Eaton FP0708R1-R09-R 90 nH 75 A Saturation Inductor

Share
pEaton FP0708R1-R09-R: 90 nH high frequency, high current power inductor, 44 A Irms, 75 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm package./p
    • Product Details
    • Download

    FP0708R1-R09-R at a glance: 90 nH high frequency, high current power inductor, 44 A Irms, 75 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm body, 7.2 mm tall.

    Eaton FP0708R1-R09-R High frequency, high current power inductors

    The FP0708R1-R09-R is a 7.0 x 8.5 mm high frequency, high current power inductor from Eaton, rated 44 A Irms at 90 nH and 0.35 mOhm typical DCR. It is a surface-mount part 7.2 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Ratings at a Glance

    Orderable part numberFP0708R1-R09-R
    Inductance, OCL (0 Adc)90 nH
    Inductance, FLL (minimum)64 nH
    Irms (40 °C rise, no core loss)44 A
    Isat (20% roll-off @ +25 °C)75 A
    Isat2 (20% roll-off @ +125 °C)60 A
    DCR typical @ +20 °C0.35 mOhm
    K-factor (Bp-p = K x L x dI)557
    Package7.0 x 8.5 mm, 7.2 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    90 nH open-circuit, 64 nH at full load: that is a 29% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 75 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 678 mW dissipated at 44 A through 0.35 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 557 turns ripple into flux: a peak-to-peak swing of 22.5 A gives about 112.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 7.0 x 8.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 90 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 2 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 90 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.35 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0708R1-R09-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products