
FP0708R1-R15-R at a glance: 150 nH high frequency, high current power inductor, 44 A Irms, 47 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm body, 7.2 mm tall.
Eaton FP0708R1-R15-R is a high frequency, high current power inductor in a 7.0 x 8.5 mm surface-mount package. It carries 150 nH of open-circuit inductance with 44 A Irms and a typical DCR of 0.35 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.2 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP0708R1-R15-R |
| Inductance, OCL (0 Adc) | 150 nH |
| Inductance, FLL (minimum) | 108 nH |
| Irms (40 °C rise, no core loss) | 44 A |
| Isat (20% roll-off @ +25 °C) | 47 A |
| Isat2 (20% roll-off @ +125 °C) | 37 A |
| DCR typical @ +20 °C | 0.35 mOhm |
| K-factor (Bp-p = K x L x dI) | 557 |
| Package | 7.0 x 8.5 mm, 7.2 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 150 nH is measured with no DC in the winding, 108 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.
Peak current at 20% roll-off is 47 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 678 mW dissipated at 44 A through 0.35 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The K-factor of 557 turns ripple into flux: a peak-to-peak swing of 14.1 A gives about 117.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 7.0 x 8.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 5 of 7 when the data sheet is sorted by inductance.
The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.35 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd