Eaton FP0805R1-R03-R 32 nH Power Inductor, 65 A
Eaton FP0805R1-R03-R 32 nH Power Inductor, 65 A

Eaton FP0805R1-R03-R 32 nH Power Inductor, 65 A

Share
pEaton FP0805R1-R03-R: 32 nH high frequency, high current power inductor, 65 A Irms, 110 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm package./p
    • Product Details
    • Download

    FP0805R1-R03-R at a glance: 32 nH high frequency, high current power inductor, 65 A Irms, 110 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm body, 5.0 mm tall.

    Eaton FP0805R1-R03-R High frequency, high current power inductors

    Eaton builds the FP0805R1-R03-R as a high frequency, high current power inductor for 7.5 x 7.6 mm footprints. At 32 nH and 65 A Irms with 0.17 mOhm of DCR it targets high-current DC-DC stages; the 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0805R1-R03-R
    Inductance, OCL (0 Adc)32 nH
    Inductance, FLL (minimum)23 nH
    Irms (40 °C rise, no core loss)65 A
    Isat (20% roll-off @ +25 °C)110 A
    Isat2 (20% roll-off @ +125 °C)95 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)823.6
    Package7.5 x 7.6 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 32 nH is measured with no DC in the winding, 23 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 110 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 718 mW dissipated at 65 A through 0.17 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 823.6 turns ripple into flux: a peak-to-peak swing of 33 A gives about 87 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 7.5 x 7.6 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 32 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 5 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 32 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.17 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0805R1-R03-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message