Eaton FP0805R1-R20-R 200 nH 20 A Saturation Inductor
Eaton FP0805R1-R20-R 200 nH 20 A Saturation Inductor

Eaton FP0805R1-R20-R 200 nH 20 A Saturation Inductor

Share
pEaton FP0805R1-R20-R: 200 nH high frequency, high current power inductor, 65 A Irms, 20 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm package./p
    • Product Details
    • Download

    FP0805R1-R20-R at a glance: 200 nH high frequency, high current power inductor, 65 A Irms, 20 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm body, 5.0 mm tall.

    Eaton FP0805R1-R20-R High frequency, high current power inductors

    Eaton builds the FP0805R1-R20-R as a high frequency, high current power inductor for 7.5 x 7.6 mm footprints. At 200 nH and 65 A Irms with 0.17 mOhm of DCR it targets high-current DC-DC stages; the 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0805R1-R20-R
    Inductance, OCL (0 Adc)200 nH
    Inductance, FLL (minimum)144 nH
    Irms (40 °C rise, no core loss)65 A
    Isat (20% roll-off @ +25 °C)20 A
    Isat2 (20% roll-off @ +125 °C)16 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)823.6
    Package7.5 x 7.6 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 200 nH. Put Isat1 through it and the figure falls to 144 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 200 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 20 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 718 mW dissipated at 65 A through 0.17 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 98.8 mT for a 6 A ripple (K = 823.6). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    The 7.5 x 7.6 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 200 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the highest inductance of the 5 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 200 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.17 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0805R1-R20-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products