Eaton FP0807R1-R07-R 70 nH Power Inductor, 45 A
Eaton FP0807R1-R07-R 70 nH Power Inductor, 45 A

Eaton FP0807R1-R07-R 70 nH Power Inductor, 45 A

Share
pEaton FP0807R1-R07-R: 70 nH high frequency, high current power inductor, 45 A Irms, 108 A Isat, DCR 79 mOhm, 8.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0807R1-R07-R at a glance: 70 nH high frequency, high current power inductor, 45 A Irms, 108 A Isat, DCR 79 mOhm, 8.0 x 7.0 mm body, 7.0 mm tall.

    Eaton FP0807R1-R07-R High frequency, high current power inductors

    FP0807R1-R07-R is one of Eaton's high frequency, high current power inductor series, 8.0 x 7.0 mm with a 7.0 mm tall profile. Electrically it offers 70 nH at 45 A Irms and 79 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP0807R1-R07-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)108 A
    DCR typical @ +20 °C79 mOhm
    K-factor (Bp-p = K x L x dI)520
    Package8.0 x 7.0 mm, 7.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 70 nH is measured with no DC in the winding, 50 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 108 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 45 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 79 mOhm that is roughly 159975 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 117.9 mT for a 32.4 A ripple (K = 520). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 8.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 7 parts in this data sheet, with the highest DCR in the series at 79 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Module (VRM), Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 70 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 79 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0807R1-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products