Eaton FP0807R1-R20-R 200 nH Power Inductor, 45 A
Eaton FP0807R1-R20-R 200 nH Power Inductor, 45 A

Eaton FP0807R1-R20-R 200 nH Power Inductor, 45 A

Share
pEaton FP0807R1-R20-R: 200 nH high frequency, high current power inductor, 45 A Irms, 38 A Isat, DCR 28 mOhm, 8.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0807R1-R20-R at a glance: 200 nH high frequency, high current power inductor, 45 A Irms, 38 A Isat, DCR 28 mOhm, 8.0 x 7.0 mm body, 7.0 mm tall.

    Eaton FP0807R1-R20-R High frequency, high current power inductors

    Eaton builds the FP0807R1-R20-R as a high frequency, high current power inductor for 8.0 x 7.0 mm footprints. At 200 nH and 45 A Irms with 28 mOhm of DCR it targets high-current DC-DC stages; the 7.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0807R1-R20-R
    Inductance, OCL (0 Adc)200 nH
    Inductance, FLL (minimum)144 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)38 A
    DCR typical @ +20 °C28 mOhm
    K-factor (Bp-p = K x L x dI)520
    Package8.0 x 7.0 mm, 7.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 200 nH is measured with no DC in the winding, 144 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 38 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 56700 mW (45 A squared times 28 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 520 and a ripple of 11.4 A the core sees roughly 118.6 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    The 8.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 200 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 6 of 7 when the data sheet is sorted by inductance, DCR sits between the 25 and 79 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Module (VRM), Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 200 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 28 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0807R1-R20-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products