Eaton FP0906R1-R28-R 51 A SMD Power Inductor, 280 nH
Eaton FP0906R1-R28-R 51 A SMD Power Inductor, 280 nH

Eaton FP0906R1-R28-R 51 A SMD Power Inductor, 280 nH

Share
pEaton FP0906R1-R28-R: 280 nH high frequency, high current power inductor, 51 A Irms, 34 A Isat, DCR 0.29 mOhm, 9.6 x 6.45 mm package./p
    • Product Details
    • Download

    FP0906R1-R28-R at a glance: 280 nH high frequency, high current power inductor, 51 A Irms, 34 A Isat, DCR 0.29 mOhm, 9.6 x 6.45 mm body, 8.0 mm tall.

    Eaton FP0906R1-R28-R High frequency, high current power inductors

    The FP0906R1-R28-R is a 9.6 x 6.45 mm high frequency, high current power inductor from Eaton, rated 51 A Irms at 280 nH and 0.29 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP0906R1-R28-R
    Inductance, OCL (0 Adc)280 nH
    Inductance, FLL (minimum)200 nH
    Irms (40 °C rise, no core loss)51 A
    Isat (20% roll-off @ +25 °C)34 A
    Isat2 (20% roll-off @ +125 °C)29 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)451
    Package9.6 x 6.45 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 280 nH. Put Isat1 through it and the figure falls to 200 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 280 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 34 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 754 mW dissipated at 51 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 128.8 mT for a 10.2 A ripple (K = 451). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 9.6 x 6.45 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 280 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 6 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 280 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0906R1-R28-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message