Eaton FP0910V2-R150-R - 150 nH Shielded Power Inductor 9.0 x 10.0 mm
Eaton FP0910V2-R150-R - 150 nH Shielded Power Inductor 9.0 x 10.0 mm

Eaton FP0910V2-R150-R - 150 nH Shielded Power Inductor 9.0 x 10.0 mm

Share
pEaton FP0910V2-R150-R: 150 nH high frequency, high current power inductor, 63 A Irms, 56 A Isat, DCR 0.125 mOhm, 9.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP0910V2-R150-R at a glance: 150 nH high frequency, high current power inductor, 63 A Irms, 56 A Isat, DCR 0.125 mOhm, 9.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP0910V2-R150-R High frequency, high current power inductors

    FP0910V2-R150-R is one of Eaton's high frequency, high current power inductor series, 9.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 150 nH at 63 A Irms and 0.125 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP0910V2-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)63 A
    Isat (20% roll-off @ +25 °C)56 A
    Isat2 (20% roll-off @ +100 °C)48 A
    Isat3 (20% roll-off @ +125 °C)45 A
    DCR typical @ +20 °C0.125 mOhm
    K-factor (Bp-p = K x L x dI)455
    Package9.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    150 nH open-circuit, 108 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 56 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 496 mW (63 A squared times 0.125 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 114.7 mT for a 16.8 A ripple (K = 455). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    The 9.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 7 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.125 mOhm, Irms of 63 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 150 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.125 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0910V2-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products