
FP0910V3-R470-R at a glance: 470 nH high frequency, high current power inductor, 44 A Irms, 17 A Isat, DCR 0.4 mOhm, 9.0 x 10.0 mm body, 9.5 mm tall.
FP0910V3-R470-R is one of Eaton's high frequency, high current power inductor series, 9.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 470 nH at 44 A Irms and 0.4 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP0910V3-R470-R |
| Inductance, OCL (0 Adc) | 470 nH |
| Inductance, FLL (minimum) | 329 nH |
| Irms (40 °C rise, no core loss) | 44 A |
| Isat (20% roll-off @ +25 °C) | 17 A |
| Isat2 (20% roll-off @ +100 °C) | 14 A |
| Isat3 (20% roll-off @ +125 °C) | 13 A |
| DCR typical @ +20 °C | 0.4 mOhm |
| K-factor (Bp-p = K x L x dI) | 340 |
| Package | 9.0 x 10.0 mm, 9.5 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 470 nH is measured with no DC in the winding, 329 nH with the winding loaded to Isat1. The gap between them is 30%, and it is the reason a converter that looks well damped at no load can ring at full current.
Saturation is quoted as 20% roll-off at 17 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Copper loss at the rated current works out at about 774 mW (44 A squared times 0.4 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 81.5 mT for a 5.1 A ripple (K = 340). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 9.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 470 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it the highest inductance of the 7 parts in this data sheet, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost, Irms of 44 A is the bottom of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 470 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.4 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd