Eaton FP1005R1-R15-R 150 nH 47 A Saturation Inductor
Eaton FP1005R1-R15-R 150 nH 47 A Saturation Inductor

Eaton FP1005R1-R15-R 150 nH 47 A Saturation Inductor

Share
pEaton FP1005R1-R15-R: 150 nH high frequency, high current power inductor, 53 A Irms, 47 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R1-R15-R at a glance: 150 nH high frequency, high current power inductor, 53 A Irms, 47 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R1-R15-R High frequency, high current power inductors

    Eaton builds the FP1005R1-R15-R as a high frequency, high current power inductor for 10.2 x 7.0 mm footprints. At 150 nH and 53 A Irms with 0.39 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1005R1-R15-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)47 A
    Isat2 (20% roll-off @ +125 °C)37 A
    DCR typical @ +20 °C0.39 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 108 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 47 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1096 mW (53 A squared times 0.39 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 14.1 A gives about 113.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 11 of 16 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.39 mOhm, Irms of 53 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 150 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.39 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1005R1-R15-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message