Eaton FP1005R2-R10-R High Current Inductor, 100 nH 0.47 mOhm
Eaton FP1005R2-R10-R High Current Inductor, 100 nH 0.47 mOhm

Eaton FP1005R2-R10-R High Current Inductor, 100 nH 0.47 mOhm

Share
pEaton FP1005R2-R10-R: 100 nH high frequency, high current power inductor, 50 A Irms, 73 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R2-R10-R at a glance: 100 nH high frequency, high current power inductor, 50 A Irms, 73 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R2-R10-R High frequency, high current power inductors

    FP1005R2-R10-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 100 nH at 50 A Irms and 0.47 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP1005R2-R10-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)73 A
    Isat2 (20% roll-off @ +125 °C)57 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 100 nH. Put Isat1 through it and the figure falls to 72 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 100 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 73 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 50 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.47 mOhm that is roughly 1175 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 21.9 A gives about 117.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 4 of 16 when the data sheet is sorted by inductance, DCR sits between the 0.39 and 0.7 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.47 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R2-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products