Eaton FP1005R2-R22-R 220 nH Power Inductor, 50 A
Eaton FP1005R2-R22-R 220 nH Power Inductor, 50 A

Eaton FP1005R2-R22-R 220 nH Power Inductor, 50 A

Share
pEaton FP1005R2-R22-R: 220 nH high frequency, high current power inductor, 50 A Irms, 33 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R2-R22-R at a glance: 220 nH high frequency, high current power inductor, 50 A Irms, 33 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R2-R22-R High frequency, high current power inductors

    Eaton builds the FP1005R2-R22-R as a high frequency, high current power inductor for 10.2 x 7.0 mm footprints. At 220 nH and 50 A Irms with 0.47 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1005R2-R22-R
    Inductance, OCL (0 Adc)220 nH
    Inductance, FLL (minimum)158 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)33 A
    Isat2 (20% roll-off @ +125 °C)26 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 220 nH. Put Isat1 through it and the figure falls to 158 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 220 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 33 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 50 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.47 mOhm that is roughly 1175 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 116.7 mT for a 9.9 A ripple (K = 536). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 14 of 16 when the data sheet is sorted by inductance, DCR sits between the 0.39 and 0.7 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 220 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.47 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R2-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products