Eaton FP1005R3-R08-R - 85 nH Shielded Power Inductor 10.2 x 7.0 mm
Eaton FP1005R3-R08-R - 85 nH Shielded Power Inductor 10.2 x 7.0 mm

Eaton FP1005R3-R08-R - 85 nH Shielded Power Inductor 10.2 x 7.0 mm

Share
pEaton FP1005R3-R08-R: 85 nH high frequency, high current power inductor, 45 A Irms, 90 A Isat, DCR 0.55 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R3-R08-R at a glance: 85 nH high frequency, high current power inductor, 45 A Irms, 90 A Isat, DCR 0.55 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R3-R08-R High frequency, high current power inductors

    FP1005R3-R08-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 85 nH at 45 A Irms and 0.55 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP1005R3-R08-R
    Inductance, OCL (0 Adc)85 nH
    Inductance, FLL (minimum)61 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)90 A
    Isat2 (20% roll-off @ +125 °C)64 A
    DCR typical @ +20 °C0.55 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    85 nH open-circuit, 61 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 90 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 1114 mW dissipated at 45 A through 0.55 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 27 A gives about 123 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 85 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 16 parts in this data sheet, DCR sits between the 0.39 and 0.7 mOhm the series covers, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 85 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.55 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R3-R08-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message