Eaton FP1005R3-R15-R 150 nH 47 A Saturation Inductor
Eaton FP1005R3-R15-R 150 nH 47 A Saturation Inductor

Eaton FP1005R3-R15-R 150 nH 47 A Saturation Inductor

Share
pEaton FP1005R3-R15-R: 150 nH high frequency, high current power inductor, 45 A Irms, 47 A Isat, DCR 0.55 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R3-R15-R at a glance: 150 nH high frequency, high current power inductor, 45 A Irms, 47 A Isat, DCR 0.55 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R3-R15-R High frequency, high current power inductors

    Eaton FP1005R3-R15-R is a high frequency, high current power inductor in a 10.2 x 7.0 mm surface-mount package. It carries 150 nH of open-circuit inductance with 45 A Irms and a typical DCR of 0.55 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.95 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1005R3-R15-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)47 A
    Isat2 (20% roll-off @ +125 °C)37 A
    DCR typical @ +20 °C0.55 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 150 nH is measured with no DC in the winding, 108 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 47 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 1114 mW (45 A squared times 0.55 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 536 and a ripple of 14.1 A the core sees roughly 113.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 11 of 16 when the data sheet is sorted by inductance, DCR sits between the 0.39 and 0.7 mOhm the series covers, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.55 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1005R3-R15-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products